Quick Links. Download this manual. Safety Instructions Read before connecting the projector. Information in this document is subject to change without notice. All rights reserved.

Author:Tot Kajikora
Language:English (Spanish)
Published (Last):25 November 2008
PDF File Size:13.5 Mb
ePub File Size:14.56 Mb
Price:Free* [*Free Regsitration Required]

Quick Links. Download this manual. Safety Instructions Read before connecting the projector. Information in this document is subject to change without notice. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. Restrictions and Disclaimers. The information contained in this document, including all instructions, cautions, and regulatory approvals and certifications, is based upon statements. Dell disclaims all liability in connection with any deficiencies. All statements or claims regarding the properties, capabilities, speeds, or qualifications of the part referenced in this document are made by the.

Dell specifically disclaims any knowledge of the accuracy, completeness, or substantiation for any such statements. Table of Contents. Bulb brightness degrades with usage. Dell recommends replacing your bulb after hours usage. Page 3 Batteries 2 1. When you need to contact Dell, use the electronic addresses, telephone numbers, and codes provided in the following table. If you need assistance in determining which codes to use, contact a local or an international operator.

To Computer: There are two possible methods of connecting to a computer. Connecting with S-video cable Page 17 Power cord S-video cable 3. Professional Installation Options: 1. Installation for wired RS remote control: There are two possible ways to connect with RS cable. Consult professional installer for cable and RS remote control software.

Refer to RS pin assignment and commands. Page 19 Turn the display on again after the projector cools down and the LCD message indicates there is no longer an overheated condition. If the problem persists, contact Dell. If the TEMP light is blinking orange and the LCD display indicates a fan failure, a projector fan has failed and the projector will automatically shut down.

If this problem persists, contact Dell. Adjusting the Projector Zoom and Focus 1. Page 21 7. Dell may require that lamps replaced under warranty be returned to Dell. Otherwise, contact your local waste disposal agency for the address of the nearest deposit site. Card Reader Installing Procedures 1. Read the Quick Set Up Card in the card reader box before installation and assemble the module according to the instructions. Note that Industry Canada regulations provided, that changes or modifications not expressly approved by Dell Inc.

Back to Contents Page Page 33 Ensure that the lens cap is removed and the projector turned on. Ensure the external graphics port of the portable computer is enabled. If you are using a Dell portable computer, press.

For other computers, consult your owner's manual. Contact Dell if the colors are not displayed correctly. Use the directional keys and Menu button to navigate through the OSD.

Press to darken the image. Press to lighten the image. Contrast Control the degree of difference between the brightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image. Page 39 Adjust the image distortion caused by horizontal shifting of the projector orientation. Auto Keystone Select On to enable the auto correction for vertical image distortion due to tilting the projector.

Select Off to disable the auto correction. Semi-Auto Keystone Select On to activate the semi-auto keystone correction for image distortion. Page 40 Degamma Degamma can be adjusted between 1 and 4. Default setting is 3 Recommended. Adjustment of the setting will change the color performance of the display. Press to increase the volume. Page 41 Select the left icon to mute the volume. Select the right icon to un-mute the volume.

Rear Projection-Desktop The projector reverses the image so you can project from behind a translucent screen. Lamp Reset Use this function only after a new lamp is installed in the projector.

Select the left Lamp Reset icon light bulb and arrow under the icon , and press the Enter button to reset the lamp timer. Press prgm button on the remote control for 1 sec to initiate the RF Learning process for the remote control.

There are 2 ways for matching the channel between the transmitter the remote control and the receiver the projector , l Auto: Press the Source button on the remote control for transmitting the signal in a new frequency which is randomly determined by the remote control. Select Reset to Default Channel tab to reset the receiver end, the projector back to the factory default channel. Press prgm button on the remote control for at least 5 sec to reset the transmitter to the factory default channel.

Page 45 The projector will always automatically search for available input signals when Auto Source is On, which is the default setting. Press the Source button with Auto Source On to automatically search for the next available input signal. Selecting Off will lock on the current input source. Set Auto-Source to Off to step through the different input signals manually.

Note 2: When swapping the foreground and background displays, the smallest screen size of foreground display will vary depending on different combinations of signal sources for PIP.

Page 48 Select True to display the photo image in native resolution. Select Full to scale the photo image to full screen. Select No to hide the photo information. Page 49 Select Yes to reset the projector to its factory default settings. Reset items include both computer image and video image settings. Computer Image Menu Computer Image- Note: this menu is only available when a computer input signal is present. Frequency Change the display data clock frequency to match the frequency of your computer graphics card.

Saturation Adjust a video image from black and white to fully saturated color. Press to decrease the amount of color in the image. Press to increase the amount of color in the image. Print page 1 Print document 50 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.


Dell Projector 4100MP User Manual

Safety Instructions Read before connecting the projector. About Your Projector. Using Your Projector. Regulatory Notices. Notes, Notices, and Cautions. Information in this document is subject to change without notice. All rights reserved.

VW3A1101 PDF

Dell 4100MP Safety Instructions



Dell 4100MP DLP projector Series Specs


Related Articles